SKU: Amprobe 4867996

Amprobe 4867996 AT-6030 Advanced Wire Tracer Kit with CT-400 Signal Clamp



• AT-6000-R Receiver
• AT-6000-T Transmitter
• TL-6000 Test Lead and Accessory Kit
• CC-6000 Hard Carrying Case
• (12) 1.5 V AA (IEC R6) Batteries (not installed)
• User Manual

• Traces wires in walls, ceilings, floors and corners
• Locates breakers and fuses
• Pinpoints shorts and opens
• High resolution 2.5" TFT LCD color display
• Two automatically selected frequency modes for reliable tracing on energized and de-energized circuits
• Compatible with optional TIC 410A Hot Stick attachment to extend your reach
• Three Transmitter signal modes
• Four Receiver tracing modes

• Measurement Category (Receiver & Transmitter): CAT III 600 V (Signal Clamp): CAT IV 600 V, CAT III 1000 V
• Operating voltage (Receiver & Transmitter):0 to 600 V AC/DC (Signal Clamp): 0 to 1000 V AC
• Operating frequency (Receiver & Transmitter): Energized: 6.25 kHz De-Energized: 32.768 kHz (Signal Clamp): Wire tracing: 32.768 kHz AC current measurement: 45 Hz to 400 Hz
• Hazardous voltage detection (Transmitter): > 30 V AC/DC
• Signal indications (Receiver): Numeric, bar graph display and audible beep (Transmitter): LEDs and audible beep
• Response time (Receiver): Tip Sensor (energized/de-energized): 500 MS NCV: 500 MS Battery voltage monitoring: 5 sec (Transmitter): Line voltage monitoring: 1 sec Battery voltage monitoring: 5 sec (Signal Clamp): Instantaneous
• Current output of signal (typical): Transmitter: Energized circuit: HI mode: 60 mA RMS, LO mode: 30 mA RMS, De-energized circuit: HI mode: 130 mA RMS, LO mode: 40 mA RMS, Loop mode: 160 mA RMS and Signal Clamp: mA/A for AC current measurement with multimeter
• Signal voltage output (nominal)Transmitter: De-energized circuit: LOW: 29 V RMS, 120 Vp-p HIGH: 33V RMS, 140 Vp-p With CT-400: loop model: 31 V RMS, 120 Vp-p Signal Clamp: De-energized circuit: 2.4 V RMS, 24 Vp-p
• Range detection (open air) Recevier: Tip sensor (Energized): Max distance via air: up to 20 ft (6.1 m), Pinpointing: approx. 1.97 in (5 cm), Tip sensor (De-energized): Max distance via air: up to 14.7 ft (4.5 m), Pinpointing: approx. 1.97 in (5 cm), NCV detection (40 to 400 Hz): Max. sensitivity: 90 V up to 6.56 ft (2 m) and Min. sensitivity: 600 V up to 0.39 in (1 cm)

Amprobe’s newest wire tracer combines a Receiver and powerful Transmitter to locate energized and de-energized wires, breakers, and fuses without having to disconnect any equipment. The Receiver features four tracing modes optimized for a range of applications. Its fully automatic breaker tracing capability saves time and eliminates the confusion of multiple false positives by detecting the highest recorded signal in a breaker or fuse. The Transmitter utilizes two optimized frequencies that allows for a clean and reliable signal. The Signal Clamp can be used in applications where there is no access to bare conductors by enabling the Transmitter to induce a signal into a wire through insulation. Whether you’re a novice user or an expert, the AT-6020 Amprobe Advanced Wire Tracer kit will help you get the job done fast. PACKED WITH TRACING MODES!: The AT-6000 series features 4 tracing modes: “Quick Scan” mode allows for quick wire detection at a longer distance, “Precision” mode precisely pinpoints wires or faults located behind walls, floors, or ceilings, “Breaker Identification” mode facilitates quick and easy breaker locating and, “Non-Contact Voltage Detection” mode utilizes passive tracing without the Transmitter to verify if a wire is energized. MEASURE A VARIETY OF CIRCUITS: Three Transmitter signal modes: “High Signal” mode for normal circuits, “Low Signal” mode for precision tracing in difficult areas and “Loop” mode for closed loop de-energized circuits. SIMPLE AND EASY-TO-USE: This Advanced Wire Tracer Kit is fully equipped with an automatic, simple user interface. Only 2 tracing frequencies for a cleaner, more reliable signal (energized 6 kHz, de-energized 33 kHz).